PDA

View Full Version : AU Atmega



DessertDog
25-05-2007, 08:54 PM
There is the file in downloads now and the exCW works fine not tested the others.
Thanks to the uploader.

jrg
25-05-2007, 09:47 PM
Tested and working in Pure

shotgun1
25-05-2007, 10:54 PM
can this fix work on a funcard4 as well

fergalsworld
25-05-2007, 11:00 PM
can this fix work on a funcard4 as well
No but check the funcard files downloads out:wink:

DessertDog
25-05-2007, 11:52 PM
can this fix work on a funcard4 as well
LMAO I think you need to do some searching m8

Shipoftheline
26-05-2007, 03:29 PM
can't get that Atmega fix working here.

Ps any chance of a Atmega section it gets kinda strange looking in the funcard place for a card fix which isn't funcard

FERNOX
26-05-2007, 03:32 PM
yea lotsa thx got it working here in pure lincs

fergalsworld
26-05-2007, 06:45 PM
can't get that Atmega fix working here.
Ps any chance of a Atmega section it gets kinda strange looking in the funcard place for a card fix which isn't funcard
What files are you writing to the card.

I will ask about a atmega section in the downloads.

DessertDog
26-05-2007, 07:50 PM
mmmmm I was always led to believe that the Atmega is really a funcard same sort of chip or something like that but yeh a atmega section sounds good.

Shipoftheline
26-05-2007, 08:19 PM
The APE v2 5C.hex file for ex-Cw

fergalsworld
26-05-2007, 08:37 PM
The APE v2 5C.hex file for ex-Cw
Note your bk and ird the erase the card
Make your exteeprom using RHv11 make a camd up tick cw and save as myexteeprom (dont convert to hex aslong as your programmer can write bin files) and write this to the exteeprom first then write the 5c.hex to the flash.
Pop it in go to bbc1 then slysporsts1 you will might get a popup message
just close it and give it 5 minutes to clear.

@DD its the flash thats different and the tuts aswell so a atmega section would make it easier to find things.

Shipoftheline
27-05-2007, 11:01 AM
I just used toxic 7 and put the APE v2 5C straight in with the clanzer software is this what I done wrong because this is what I've always done ?

fergalsworld
27-05-2007, 03:09 PM
I just used toxic 7 and put the APE v2 5C straight in with the clanzer software is this what I done wrong because this is what I've always done ?
No thats right all you needed to do was write the 5c to the flash.
Try RHV11 see if that works.

kaloo
28-05-2007, 01:54 AM
hi,their is their any flash file for tw ape.v2??

DessertDog
28-05-2007, 08:38 AM
hi,their is their any flash file for tw ape.v2??
You could try looking first it helps sometimes

Shipoftheline
28-05-2007, 01:31 PM
yay got it working at last

fergalsworld
28-05-2007, 01:49 PM
yay got it working at last
Are you going to enlighten us how or is it a secret:-?

Shipoftheline
28-05-2007, 02:22 PM
Are you going to enlighten us how or is it a secret:-?


Er well it may sound strange but I did the opposite to what the instructions said. I put the hex where the flash is supposed to go and the flash where the hex is meant to go

DessertDog
30-05-2007, 09:00 PM
Can someone help me regarding downloading latest atmega files
yes increase your post count
and dont keep asking the same question your post have been reduced make them constructive or you will never get your post count up.
DD

fergalsworld
30-05-2007, 09:22 PM
These links for atmega files are not accessible for me what should i do.
READ the rules here
http://world-of-digital.com/forums/f4/rules-we-try-stick-just-few-2898.html

ssmacc
31-05-2007, 01:32 PM
The APE v2 5C.hex file for ex-Cw

Confirmed I?m using the ?APE v2? in Ex C&W and no problems, actually noticed it updating yesterday (I assume I?m usually out when it updates) never changed channel and seen a blank screen before! Waited 30 mins and turned over back on?its like AU magic!

USB Infinity Programmer
APE v2 (new and appreciated ATMEGA Download Section)
Windows XP (wouldn?t work with Vista 64)
And my old file which worked with v3 AU (didn?t change it at all)

Hope this helps

Shipoftheline
31-05-2007, 02:49 PM
Yea I got a messege from the box yesterday saying updating so I presume that was a key change