PDA

View Full Version : just brough another motorola surfboard 4100 bust i think



youngie
18-01-2007, 02:58 PM
hello all i have just brought another motorola surboard 4100 with hack ware on so it says but i think i have been dane as for the last one a got i just entered mac address and config file name but this one says this

Software Version: SB4100-FIBERWARE-9F4
Hardware Version: 0
MIB Version: II
GUI Version: 1.0
VxWorks Version: 5.3

FiberCoax 'config' file information.
With thanks to all who openly share their knowledge.
Config to use on next boot: ISPs config
Current 'Config' file name: No 'config' filename available yet.

Config buffer:
No TFTP Info available

am i being stuppied again or not has i dont see anywhere to place my hack into please do help if you can very kind regards youngie

youngie
18-01-2007, 04:52 PM
anyone please lol

LincCracker
18-01-2007, 06:41 PM
hope this helps you out m8

To be able to use this features, simply do this:

http://192.168.100.1/ + flag, whereas the flags are :

---------------------------------------------------

-= FLAGs =-


flag /00-
Allows firmware Updates (by default all updates are disabled)
ex.:

- http://192.168.100.1/00-
- To restore defaults : reboot the cablemodem


flag /01-
(Stealth mode)
ex.:
- http://192.168.100.1/01-
- To restore defaults : reboot the cablemodem



/04- set config name to NVRam
ex.:
- http://192.168.100.1/04-blah.cm
- To go back to ISP defaults : http://192.168.100.1/04-
(check the config name that was set, on the fibercoax tab)


/05- boot from Stand alone kernel
ex.:
- http://192.168.100.1/05-

We left this feature for advanced users that wants to change FW's temporarily (an example would be going to docsis 1.1 FW and back to 1.0) and also to prove that serial cables isnt needed to do this. Rebooting will restore our FW from flash

/06- Sets snmp port to defaults

/24- Set memory location to dump (uppercase alpha)
ex.:
- http://192.168.100.1/24-80589680
(check the dump results on the fibercoax tab)


"07-" followed by UPPER case 6-byte hex will change HFC MAC address
(http://192.168.100.1/07-0123456789AB - stands for 01:23:45:67:89:AB)

flag "08-" followed by 24 digits will change serial number
(http://192.168.100.1/08-123456789012345678901234)

---------------------------------------------------

-= FAQ =-


Q.) When using the flag do i need to put the ' - ', ex.: /00- ?
A.) Yes

Q.) What is the stealth mode afterall for ?
A.) It disables the HFC interface and releases the HFC IP, which is used by ISPs so to access your cablemodem, via SNMP and others.

Q.) Using flag /01- , will i loose network access (internet) ?
A.) No, you won't. It will make your cablemodem stealthy against intrusions, from the HFC side.

Q.) Where can i see the config name that i'm using atm ?
A.) Go to the fibercoax tab, and it will be on the top of the page

Q.) Will i have to enter the config file name, each time i reboot ?
A.) No. the config file name that you have set previously, will be retained after booting

youngie
18-01-2007, 07:28 PM
cheers mate i have enterd the address in mate i have it up and runing now god i feal great cheers mate kind regards youngie

LincCracker
19-01-2007, 06:23 PM
glad to help m8. although i would recomend you change the firmware too hackware as it is much easier , here is a link for you

http://members.aceweb.com//madcow007/cable/docsis/hackware/SB4100-0.4.4.5-SCM01-NOSH-2.03.hex.st.rar

Cableguy69
19-01-2007, 11:27 PM
If you do ever Knacker a moto 4100/4200 you can always recover it using a max232/233 or Blackcat the info is in the Haynes Guide which I compiled, it's on here although I didn't post it, but itis here some where just do a search.