-
getting same message with the 1.3.3.4 and i was already using the other one which you've linked to
gяσωιηg σℓ∂ ιѕ мαη∂αтσяу; gяσωιηg υρ ιѕ σρтισηαℓ.
If you would like to help with the running costs of the site click below
Hidden Content
Honesty is better than sugar coated bullsh!t
-
Go to device manager and right click on comport your using pick properties and change baudrate to 115200 and set to Xon \ Xoff see if that helps
D I S C LA I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader.
I am not responsible for what you do with it!
-
ive seen that already while i googled it didn't work
gяσωιηg σℓ∂ ιѕ мαη∂αтσяу; gяσωιηg υρ ιѕ σρтισηαℓ.
If you would like to help with the running costs of the site click below
Hidden Content
Honesty is better than sugar coated bullsh!t
-
Post Thanks - 1 Thanks, 0 Likes
-
Hidden Content Originally Posted by
berley
Hidden Content
tried flashing with dream up, opened dream up used com port 1 put a tick in "use network" all other boxes were blank (wouldn't let me input anything anyhow as i tried)pressed connect, got the message "connection prepared now switch on the dreambox" switched it on and got this message "is not a valid integer value"
Ok to fix the "is not a valid integer value" and successfully flash your box, try this method (if you have a router).
Go to device manager and right click on the com port you are using and pick properties
Change baudrate to 115200
Change Flow control to Xon / Xoff
click ok and close
Now Plug ethernet cable into box and router
plug ethernet cable into pc and router ( check what ip its been given and also check you can get on the net )
Plug null modem cable in to pc and dreambox
Now open dreamup 1.3.4.4
Choose the Com Port the null modem cable is connected to
tick use network box and put ip of pc in top box and ip of DM in bottom box
click connect it should say connection prepared switch on dreambox
plug power into dreambox and turn it on
Dreamup will now send the "Flashloader" to your dream.
If an error message appears press ok to close it
in the window it should say something like now in http or html mode
1:Now open a web browser on your pc and put the ip address in and press enter
The box will now be forced into "Bootloader stage".
It can take a long time before it connects to the dreambox.
Just have patience.
The web flash interface will open.
Select "firmware upgrade" at the bottom of the webpage
Select the image file (must be an NFI file) you want to flash in the dream.
Press the flash button and see if you get the flash progress % going along (it could take a minute to start be patient)
wait until you get the blue blocks and the finished message, you can now close everything down including dreamup
take cables out of the dreambox and restart it and it should boot up ok (be patient).
Try these if the above don't work
Start from the very beginning again and up to
Dreamup will now send the "Flashloader" to your dream.
If an error message appears press ok to close it now do the following
2: Dont open the web browser just click the flash button on dreamup and choose the nfi image to flash and see if it starts to flash,
If it dont,
3: Start from the beginning again but this time leave the ip's in dreamup but untick the use network box and click connect
Dreamup will now send the "Flashloader" to your dream.
If an error message appears press ok to close it
now click flash in dreamup and choose nfi image to flash
the last 2 choices could take anything upto 40 mins to flash because you are doing it via a nullmodem cable only, even thought the ethernet cable is plugged in
you will know if its flashing as it will say so in the window
The first option is the quickest way and usually works.
Last edited by fergalsworld; 03-05-2015 at 05:14 PM.
D I S C LA I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader.
I am not responsible for what you do with it!
-
Post Thanks - 1 Thanks, 0 Likes
-
First option worked Hidden Content
gяσωιηg σℓ∂ ιѕ мαη∂αтσяу; gяσωιηg υρ ιѕ σρтισηαℓ.
If you would like to help with the running costs of the site click below
Hidden Content
Honesty is better than sugar coated bullsh!t
-
Post Thanks - 1 Thanks, 0 Likes
Bookmarks