Hi all
When i connect my clone dm600 it keeps coming up
" integer not a true value
trying to reflash box with new image
any ideas?
thanks
ian
Hi all
When i connect my clone dm600 it keeps coming up
" integer not a true value
trying to reflash box with new image
any ideas?
thanks
ian
if i remember correctly buck, when you bring up dream-up, it should recognise your box, you then go and upload your image to dream-up, you then start dream-up, and then you plug in your dreambox to the mains,
Hope this helps m8
.................................................. .................................................. .
LIFE`S A BITCH .......... THEN YOU DIE !!
NEVER TAKE LIFE SERIOUSLY.... NOBODY GETS OUT ALIVE ANYWAY Hidden Content
Hidden Content
Hidden Content Hidden Content
will try that tonight, cheers buck
Is there anykind of image currently flashed to the box?
You may just be able to ftp a new image to /tmp/ the flash the box via telnet.
D I S C L A I M E R My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it.
Here's a couple more methods of flashing a DM600: -
Important, You must know what IP address your DB will have, post flash erase. My DB always gets the same IP address from the router when I use DHCP. The IP is assigned based on MAC address, so never changes from image to image.
If someone else can, please chip in with a way of figuring out your IP address otherwise.
1: Turn on DHCP in the communications page and note down the IP address your DB was assigned.
2: Remove the power supply lead from the back of the DB, hold in the power/standby button, plug in the power supply again (While keeping the button pressed). Give it about 15 secs and flash should be erased.
It only actually takes about 10 secs, You will notice that the flashing pattern on the LEDs will have changed.
3: Open up your favorite web browser and type in the IP address you noted earlier. You will see a green page load. Click the link labeled 'upgrade firmware' (or similar) on the bottom left of the page. Browse to and select your the NFI image file on your PC. Click the button to proceed.
4: Once the flash progress meter has reached 100%, turn the DB off then on again.
That's it, You have a new image in flash.
Method 2.
telnet dreambox-ip and the execute the following commands :
mount /boot -o remount,rw
rm /boot/*
reboot
Then type the DM600 ip into internet explorer & select firmware upgrade, then browse to your new image.
D I S C L A I M E R My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it.
sic
telnet worked a treat but still a few teething problems which im sure I will sort out when im not a one eyed beer monster dribbling whilst doint it like i was last night.
Cheers mate
Buck
Post the issues in the DM600 section, i'm sure we can get them sorted Hidden Content
D I S C L A I M E R My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it.
Cough Cough, That text looks familiar. Hidden Content
as wullboy said do it that way ...if u have to di it agn ...as most of the images now days are recomended to use ser cable and dreamup or outher prog
anyway we all do it differnt er
Bookmarks