some posts suggest 41063 still on 3.6 but didn't work for me, but i found bytes for 3.7 published which defo work
Type: Posts; User: bammy; Keyword(s):
some posts suggest 41063 still on 3.6 but didn't work for me, but i found bytes for 3.7 published which defo work
Personally I'd keep my money safe in the piggybank for a few months until we see if any third party boxes work after the Nagra3 rollout...
when you say 'pulled the red jumper out but netid stayed the same' - what is the netid being reported in the EM? is it 09999 by any chance? If so you need to set it using either libby or the...
That's not the point... I don't need the box, just enjoy the challenge of making it work :)
Picked up an old Pace 2000 at the Sunday car boot sale, got the BK off the card so programmed it up ready to go. First problem was ticking power supply, found shorted cap so replaced that and the...
flash is a hex file and ext eep is a bin file
I *think* it goes back to ----- or ***** on a 4001 (but can't be 100% sure as I've hadly ever seen a 4001 being in exC&W) - but you should be able to set it with libby. Have you managed to get it to...
It depends what version of firmware is on the box - Bromley (exC&W) or Langley (pure). If you post up this info someone can give you the correct byte.
Do you mean bod or bd0? If bd0 then likely you have a blockered image on the card. You can't get into the card without running mrom (which will destroy the information you are trying to get) but...
If you're in 41060 then you're in a exC&W area so you've not really got the right box for your area. The netid will autoset on this box in pure NTL areas but (as you've experienced) it will set...
And what area are you in?
If you've got a config file try deleting it.
Is the netid set? if not, connect it to a feed, let it find the netid (as you're in pure should set itself), then try to read the bytes.
Is it a 4000N in a telewest area or a 4000T in a exC&W area? If so that will be the problem.
Sounds like your battery is dead - check it with a voltmeter.
When you say 'all it does is scroll numbers' - how long are you leaving it? Once the numbers have finished scrolling it will alternate between ERAS & LAIT for a while and should eventually reboot. ...
You can jtag the 2100 but not the 2110
well if you're still on CR1 then presumably the box has the anti-update mod done? but that's just the start of your problems if you want to get movies back :)
Don't know about the 2110 (which involves capacitors) but on the 2100 the two 'resistors' which you remove are infact just straight links (so can be replaced with a wire link)
You need to supply more info such as the card revision (you can get this from the engineer's menu). Likely it will be a rev A86 or B0D, both of which will need glitching before you can read the...
It's not an image problem, it's to do with the talkback not being connected when the box takes a firmware update (and therefore being unable to obtain a valid mac address. allegedly). Is rumoured to...
You can do a forced update and the method has been posted many times before so won't repeat it here - however, just because the SA box has taken the new firmware, this does not mean it is available...
Almost certainly a tuner or on board capacitor is in the process of dying - will probably continue to get worse until the box is completely dead. These failures can be traced but it tends to be very...
The card itself isn't 'donald ducked' - you can reuse it but you'll have to get you BK off the box itself (think a chip needs lifting/reading on these boxes)
Sounds like a fake BK
Where did you gte the boxkey from and are you 100% sure it's genuine? Does it start 6D? Assuming you got it by glitching the card, was the IRD correct on the card?
What do you mean by 'all info comes back ok'? It would help if you could include the output from Nagra - that way someone will be able to advise on what you need to do to reuse the cards.
The byte depends on the firmware version on the box - check at the top of the last page in the engineer's menu.
This doesn't answer the question, but I've got to ask - why are you doing it this way rather than jtag?
If your card was hit you won't be able to read the details from it; you'll have to rely on the backup record that I'm sure you carefully wrote down :) or read the information from the box (and the...
look in eng menu and check card status (i) with card inserted (ii) with card removed - this could be a hardware fault on the box
the 2000 won't be in there - the only way is to lift the atmels. there is a very slim chance that the 1000ph1b boxes will be in there but you're almost certainly looking at a led simm job to get the...
If you post the firmware version (top of the last page in the em) then someone will advise you of the correct byte location for the bk.
You won't get it - ever - due to the way the system now works.
gwapo, what firmware version is the box running? It could be that it has the antiupdate mod applied which is preventing it from taking a firmware update.
@gaza, you're off topic - need to start...
If you're hoping to use the ledsimm on a samsung I think you're in for a fruitless weekend:)
PS I live in Canada does it matter?
Er, just slightly :) Not wishing to be rude but this is a UK site and you're going to find very little in the way of help for Canadian suppliers. Is there no...
why restrict yourself to sa models? pace are much easier to crack!
where did you get the image from?
Think the problem is with the operator, not the software :)
funprog communicates via the parallel post, not the serial port (hence the lpt error)