Search:

Type: Posts; User: bammy; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: 3.7 to 3.6

    by bammy
    Replies
    1
    Views
    1,079

    Re: 3.7 to 3.6

    some posts suggest 41063 still on 3.6 but didn't work for me, but i found bytes for 3.7 published which defo work
  2. Thread: Which Box

    by bammy
    Replies
    12
    Views
    2,729

    Re: Which Box

    Personally I'd keep my money safe in the piggybank for a few months until we see if any third party boxes work after the Nagra3 rollout...
  3. Replies
    4
    Views
    1,855

    Re: pace 1000 stuck on ap52 when loading

    when you say 'pulled the red jumper out but netid stayed the same' - what is the netid being reported in the EM? is it 09999 by any chance? If so you need to set it using either libby or the...
  4. Replies
    2
    Views
    1,162

    Re: DiTV2000 - Pixellation & Sound Problem

    That's not the point... I don't need the box, just enjoy the challenge of making it work :)
  5. Replies
    2
    Views
    1,162

    DiTV2000 - Pixellation & Sound Problem

    Picked up an old Pace 2000 at the Sunday car boot sale, got the BK off the card so programmed it up ready to go. First problem was ticking power supply, found shorted cap so replaced that and the...
  6. Thread: funcard Question

    by bammy
    Replies
    1
    Views
    880

    Re: funcard Question

    flash is a hex file and ext eep is a bin file
  7. Replies
    4
    Views
    1,328

    Re: 4001n - slow - no channels only freeview

    I *think* it goes back to ----- or ***** on a 4001 (but can't be 100% sure as I've hadly ever seen a 4001 being in exC&W) - but you should be able to set it with libby. Have you managed to get it to...
  8. Thread: jtag

    by bammy
    Replies
    2
    Views
    1,007

    Re: jtag

    It depends what version of firmware is on the box - Bromley (exC&W) or Langley (pure). If you post up this info someone can give you the correct byte.
  9. Replies
    1
    Views
    905

    Re: Urgent Help Needed

    Do you mean bod or bd0? If bd0 then likely you have a blockered image on the card. You can't get into the card without running mrom (which will destroy the information you are trying to get) but...
  10. Replies
    4
    Views
    1,328

    Re: 4001n - slow - no channels only freeview

    If you're in 41060 then you're in a exC&W area so you've not really got the right box for your area. The netid will autoset on this box in pure NTL areas but (as you've experienced) it will set...
  11. Replies
    4
    Views
    1,290

    Re: Pace DI4000 - Talkback stopped working

    And what area are you in?
  12. Thread: mrom problem

    by bammy
    Replies
    1
    Views
    963

    Re: mrom problem

    If you've got a config file try deleting it.
  13. Replies
    2
    Views
    1,172

    Re: sammy jtag bytes problem

    Is the netid set? if not, connect it to a feed, let it find the netid (as you're in pure should set itself), then try to read the bytes.
  14. Replies
    4
    Views
    1,290

    Re: Pace DI4000 - Talkback stopped working

    Is it a 4000N in a telewest area or a 4000T in a exC&W area? If so that will be the problem.
  15. Re: sammy 2100 pin changes. then goes back to no bin when i reboot box

    Sounds like your battery is dead - check it with a voltmeter.
  16. Replies
    2
    Views
    1,041

    Re: Pace 1000 phase 1b

    When you say 'all it does is scroll numbers' - how long are you leaving it? Once the numbers have finished scrolling it will alternate between ERAS & LAIT for a while and should eventually reboot. ...
  17. Thread: 2100c

    by bammy
    Replies
    1
    Views
    1,078

    Re: 2100c

    You can jtag the 2100 but not the 2110
  18. Replies
    1
    Views
    917

    Re: problem getting movie channels

    well if you're still on CR1 then presumably the box has the anti-update mod done? but that's just the start of your problems if you want to get movies back :)
  19. Replies
    1
    Views
    718

    Re: Resistor Values Need

    Don't know about the 2110 (which involves capacitors) but on the 2100 the two 'resistors' which you remove are infact just straight links (so can be replaced with a wire link)
  20. Thread: box 2000

    by bammy
    Replies
    1
    Views
    1,053

    Re: box 2000

    You need to supply more info such as the card revision (you can get this from the engineer's menu). Likely it will be a rev A86 or B0D, both of which will need glitching before you can read the...
  21. Replies
    12
    Views
    2,423

    Re: Sky movies 9 locked, help??

    It's not an image problem, it's to do with the talkback not being connected when the box takes a firmware update (and therefore being unable to obtain a valid mac address. allegedly). Is rumoured to...
  22. Replies
    2
    Views
    771

    Re: How to upgrade box to Virgin

    You can do a forced update and the method has been posted many times before so won't repeat it here - however, just because the SA box has taken the new firmware, this does not mean it is available...
  23. Replies
    2
    Views
    1,069

    Re: Pace 2000 Freezing / Taking Ages to Start

    Almost certainly a tuner or on board capacitor is in the process of dying - will probably continue to get worse until the box is completely dead. These failures can be traced but it tends to be very...
  24. Replies
    4
    Views
    1,723

    Re: What does this mean?

    The card itself isn't 'donald ducked' - you can reuse it but you'll have to get you BK off the box itself (think a chip needs lifting/reading on these boxes)
  25. Thread: 2110

    by bammy
    Replies
    6
    Views
    1,773

    Re: 2110

    Sounds like a fake BK
  26. Thread: 2110

    by bammy
    Replies
    6
    Views
    1,773

    Re: 2110

    Where did you gte the boxkey from and are you 100% sure it's genuine? Does it start 6D? Assuming you got it by glitching the card, was the IRD correct on the card?
  27. Replies
    2
    Views
    1,348

    Re: card locked or not

    What do you mean by 'all info comes back ok'? It would help if you could include the output from Nagra - that way someone will be able to advise on what you need to do to reuse the cards.
  28. Replies
    5
    Views
    1,142

    Re: Samsung debug tool

    The byte depends on the firmware version on the box - check at the top of the last page in the engineer's menu.
  29. Replies
    4
    Views
    1,349

    Re: Sammy TSOP removal

    This doesn't answer the question, but I've got to ask - why are you doing it this way rather than jtag?
  30. Re: original n#l card hit in november but need ird and bk

    If your card was hit you won't be able to read the details from it; you'll have to rely on the backup record that I'm sure you carefully wrote down :) or read the information from the box (and the...
  31. Replies
    6
    Views
    1,400

    Re: yet another 1000 ph 1b problem

    look in eng menu and check card status (i) with card inserted (ii) with card removed - this could be a hardware fault on the box
  32. Replies
    3
    Views
    1,130

    Re: b/k database help

    the 2000 won't be in there - the only way is to lift the atmels. there is a very slim chance that the 1000ph1b boxes will be in there but you're almost certainly looking at a led simm job to get the...
  33. Replies
    7
    Views
    1,870

    Re: Bk Number ??????? HELP PRETTY PLEASE

    If you post the firmware version (top of the last page in the em) then someone will advise you of the correct byte location for the bk.
  34. Thread: ntl vod

    by bammy
    Replies
    5
    Views
    1,299

    Re: ntl vod

    You won't get it - ever - due to the way the system now works.
  35. Replies
    23
    Views
    3,964

    Re: Pace DITV-1000 Phase 1b

    gwapo, what firmware version is the box running? It could be that it has the antiupdate mod applied which is preventing it from taking a firmware update.

    @gaza, you're off topic - need to start...
  36. Thread: sammy 2100c

    by bammy
    Replies
    2
    Views
    1,219

    Re: sammy 2100c

    If you're hoping to use the ledsimm on a samsung I think you're in for a fruitless weekend:)
  37. Replies
    17
    Views
    3,085

    Re: Tutorial on fixing cable box, is it valid

    PS I live in Canada does it matter?

    Er, just slightly :) Not wishing to be rude but this is a UK site and you're going to find very little in the way of help for Canadian suppliers. Is there no...
  38. Replies
    17
    Views
    3,085

    Re: Tutorial on fixing cable box, is it valid

    why restrict yourself to sa models? pace are much easier to crack!
  39. Replies
    4
    Views
    1,581

    Re: rom11 help needed

    where did you get the image from?
  40. Replies
    2
    Views
    997

    Re: problem with funprog

    Think the problem is with the operator, not the software :)

    funprog communicates via the parallel post, not the serial port (hence the lpt error)
Results 1 to 40 of 212
Page 1 of 6 1 2 3 4